The structural analysis software RFEM 6 is the basis of a modular software system. The main program RFEM 6 is used to define structures, materials, and loads of planar and spatial structural systems consisting of plates, walls, shells, and members. The program also allows you to create combined structures as well as to model solid and contact elements.
RSTAB 9 is a powerful analysis and design software for 3D beam, frame, or truss structure calculations, reflecting the current state of the art and helping structural engineers meet requirements in modern civil engineering.
Do you often spend too long calculating cross-sections? Dlubal Software and the RSECTION stand-alone program facilitate your work by determining section properties of various cross-sections and performing a subsequent stress analysis.
Do you always know where the wind is blowing from? From the direction of innovation, of course! With RWIND 2, you have a program at your side that uses a digital wind tunnel for the numerical simulation of wind flows. The program simulates these flows around any building geometry and determines the wind loads on the surfaces.
Are you looking for an overview of snow load zones, wind zones, and seismic zones? Then you are in the right place. Use the Geo-Zone Tool to determine quickly and efficiently snow loads, wind speeds, and seismic data according to ASCE 7‑16 and other international standards.
Would you like to try out the capabilities of the Dlubal Software programs? You have the opportunity to do so! The free 90-day full version allows you to thoroughly test all our programs.
This webinar will provide the design workflow for multistory CLT buildings acc. to the CSA O86:19 in RFEM 6.
This webinar will provide an introduction to steel connection design acc. to the AISC 360-22 in RFEM 6.
This webinar will provide an introduction to steel member design acc. to the AISC 360-22 and 341-22 in RFEM 6.
Free Webinar | RWIND 2 - Calculating Wind Loads with CFD Simulation (USA)
This webinar will provide an overview of calculating wind loads using CFD simulation with RWIND 2 and RFEM 6.
Free Webinar | Introduction to Time History Analysis in RFEM 6 (USA)
This webinar will provide an introduction to time history analysis in RFEM 6.
Free Webinar | Stability Analysis in RFEM 6 (USA)
This webinar will provide an introduction to stability analysis in RFEM 6.
Integrated Rhino/Grasshopper Workflows in RFEM 6 (USA)
This webinar will provide an introduction to integrated Rhino/Grasshopper workflows in RFEM 6.
Free Webinar | NBC 2020 Response Spectrum Analysis in RFEM 6 (USA)
This webinar will provide an introduction to a response spectrum analysis acc. to the NBC 2020 in RFEM 6.
Free Webinar | CSA A23.3:19 Concrete Building Design in RFEM 6 (USA)
This webinar will provide an introduction to concrete building design acc. to the CSA A23.3:19 in RFEM 6.
Free Webinar | AISI S100 / CSA S136 Cold-Formed Steel Design in RFEM 6 (USA)
This webinar will provide an introduction to cold-formed steel member design acc. to the AISI S100 / CSA S136 in RFEM 6.
Free Webinar | AISC 360-16 Steel Connection Design in RFEM 6 (USA)
This webinar will provide an introduction to steel connection design using FEA acc. to the AISC 360-16 in RFEM 6.
Free Webinar | 2018 NDS CLT Design in RFEM 6 (USA)
This webinar will provide an introduction to cross-laminated timber (CLT) design acc. to the 2018 NDS in RFEM 6.
Free Webinar | Steel Silo Design in RFEM 6 (USA)
This webinar will provide an introduction to steel silo design in RFEM 6.
Free Webinar | CSA S16:19 Steel Design in RFEM 6 (USA)
This webinar will provide an introduction to steel design acc. to the CSA S16:19 in RFEM 6.
Free Webinar | Reinforced Concrete Tank Design in RFEM 6 (USA)
This webinar will provide an introduction to reinforced concrete tank analysis and design in RFEM 6.
Free Webinar | Revit, IFC, and DXF Integration in RFEM 6 (USA)
This webinar will provide an introduction to BIM integration including Revit, IFC, and DXF in RFEM 6.
Free Webinar | Construction Stages Analysis in RFEM 6 (USA)
This webinar will provide an introduction to construction stage analysis and design in RFEM 6.
Free Webinar | Rhino/Grasshopper Integration in RFEM 6 (USA)
This webinar will provide an introduction to Rhino/Grasshopper integration in RFEM 6.
Free Webinar | Member, Surface, and Solid Stress-Strain Analysis in RFEM 6 (USA)
This webinar will provide an introduction to member, surface, and solid stress-strain analysis in RFEM 6.
Free Webinar | CFD Wind Simulation with RWIND 2 (USA)
This webinar will provide an introduction to CFD wind analysis utilizing RWIND 2 and RFEM 6.
Free Webinar | ADM 2020 Aluminum Design in RFEM 6 (USA)
This webinar will provide an introduction to aluminum member design acc. to the ADM 2020 in RFEM 6.
Free Webinar | ASCE 7-16 Response Spectrum Analysis in RFEM 6 (USA)
This webinar will provide an introduction to a response spectrum analysis acc. to the ASCE 7-16 in RFEM 6.
Free Webinar | Tensile Membrane Structure Design in RFEM 6 (USA)
This webinar will provide an introduction to tensile membrane structure design in RFEM 6.
Free Webinar | NDS 2018 Timber Member Design in RFEM 6 (USA)
This webinar will provide an introduction to timber member design acc. to the NDS 2018 in RFEM 6.
Free Webinar | ACI 318-19 Concrete Design in RFEM 6 (USA)
This webinar will provide an introduction to concrete design acc. to the ACI 318-19 in RFEM 6.
Free Webinar | AISC 360-16 Steel Design in RFEM 6 (USA)
This webinar will provide an introduction to steel design acc. to the AISC 360-16 in RFEM 6.
This webinar will provide an introduction to the new generation FEA software RFEM 6.
Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.
This webinar demonstrates structural blast loading utilizing a time history analysis in RFEM.
This webinar demonstrates a response spectrum analysis according to the NBC 2015 in RFEM and the RF-DYNAM Pro add-on modules.
This webinar demonstrates the general concrete design workflow according to the ACI 318-19 in RFEM and the RF-CONCRETE add-on modules.